[SEL] John Deere 1 1/2hp E ignitor

[Dave Otto]

Hi Curt

A couple things maybe you haven't tried. While cranking the engine as fast
as you can rub the mag wire over the springs on the ignitor and you should
get some nice sparks, as long as they're not covered with paint. Also the
timing of the ignitor trip to the position of the armature is very
important. At the point your ignitor trips the little rivet in the rear mag
cover needs to drop into the detent of the armature. Even the slop in the
bolt holes of the ignitor can mess up the timing if you remove and
re-install the ignitor. 

Many years ago I struggled with my JD and two things caused me problems; I
added too much oil in the rear cup and fouled the collector ring, which
someone has already mentioned. And the timing between the mag and ignitor.

I hope this may help,
Dave



-----Original Message-----
From: sel-bounces at lists.stationary-engine.com
[mailto:sel-bounces at lists.stationary-engine.com] On Behalf Of
cgandree at mchsi.com
Sent: Thursday, August 10, 2017 7:28 AM
To: The SEL email discussion list
Subject: Re: [SEL] John Deere 1 1/2hp E ignitor

Not yet John, but that's an idea I hadn't tried.  However, there is small
engine show this weekend nearby and many of my engine goroos will be there
so plan to take the old girl and seek help.
Thanks,
Curt

----- Original Message -----
From: jbcast at charter.net
To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
Sent: Sunday, August 6, 2017 6:18:07 AM
Subject: Re: [SEL] John Deere 1 1/2hp E ignitor

Have you tried battery and coil to be sure everything else is OK?
J.B.

	-----------------------------------------From: cgandree at mchsi.com
To: "The SEL email discussion list"
Cc: 
Sent: 06-Aug-2017 10:47:07 +0000
Subject: Re: [SEL] John Deere 1 1/2hp E ignitor

 Jim I purchased a complete new housing that had new bearings, etc.
Then re-assembled and charged the magnets.
 I am leaning towards my timing is off and need to make those adjustments.
Hopefully get it running again soon.
 Thanks,
 Curt

 ----- Original Message -----
 From: "Jim Ritenour" 
 To: "The SEL email discussion list" 
 Sent: Tuesday, August 1, 2017 6:21:59 PM
 Subject: Re: [SEL] John Deere 1 1/2hp E ignitor

 I saw you rebuilt the mag what exactly did you do? Did you have the
bushings replaced? This can be tricky if your machine is not set up
correctly.

 Sent from my iPhone

 > On Aug 1, 2017, at 2:52 PM, Judge Tommy Turner  wrote:
 >
 > Tom is correct. If using a mag the points should stay closed and only
open  > when the ignitor snaps. If using a battery and coil the points
should  > always remain open and only close when the ignitor is tripped.
 >
 > Tommy Turner
 >
 >
 >
 > -----Original Message-----
 > From: sel-bounces at lists.stationary-engine.com
 > [mailto:sel-bounces at lists.stationary-engine.com] On Behalf Of Tom Winland
> Sent: Tuesday, August 01, 2017 2:23 PM  > To: The SEL email discussion
list  > Subject: Re: [SEL] John Deere 1 1/2hp E ignitor  >  > The point stay
closed when using the mag and open when using a battery and  > coil  >  >
Tom Winland  > Aka GasEngineTom  > Sent from my iPhone  >  >> On Aug 1,
2017, at 1:13 PM, Ed Herreid  wrote:
 >>
 >> Curt,
 >>
 >>
 >> Pretty sure the points should be open. When the igniter is tripped it  >
closes quickly and then stays open. Possibly one of the springs in  >
reversed? If it is closed all the time the coil/mag is going to get hot.
 >>
 >>
 >> Also common is the wiper on the mag part getting oily and slicked up and
> not making good contact. Every once in a while I have to remove the little
> screw cap on top and take a pencil eraser with a rag covering and clean it
> up. Check the little contact on the end of the spring and clean it up if
> needed too.
 >>
 >>
 >> Ed Herreid
 >>
 >>
 >> ________________________________
 >> From: sel-bounces at lists.stationary-engine.com
 >>  on behalf of
 >> cgandree at mchsi.com
 >> Sent: Monday, July 31, 2017 10:51 PM  >> To: Old eng list ; The SEL
email discussion list  >> Cc: cgandree at aol.com  >> Subject: [SEL] John Deere
1 1/2hp E ignitor  >>  >> Ok guys I just rebuilt my magnito on my JD 1 1/2 E
and charged it  >> properly. After putting it back on the engine and making
sure that

 >> the gears were at the marks as before I attempted to start the engine
>> but no go. I removed the ignitor and cleaned and oiled everything so the
> it would trip properly. Tried to turn it over but still no go. My question
> is, should the points on this ignitor be open or closed? Mine are closed.
 > Sure would likes some words of wisdom from the group.
 >> Thank you in advance.
 >> Curt Andree
 >> _______________________________________________
 >> SEL mailing list
 >> SEL at lists.stationary-engine.com
 >>  >> o/sel>
 >> www.stationary-engine.com
 >> This is the "the" SEL list. The home of the original email based  >
disccusion list for stationary-engines. To see the collection of prior  >
postings to the list ...
 >>
 >>
 >>
 >> _______________________________________________
 >> SEL mailing list
 >> SEL at lists.stationary-engine.com
 >>  >
 > _______________________________________________
 > SEL mailing list
 > SEL at lists.stationary-engine.com
 >  _______________________________________________
 SEL mailing list
 SEL at lists.stationary-engine.com

_______________________________________________
SEL mailing list
SEL at lists.stationary-engine.com
http://www.stationary-engine.com/mailman/listinfo/sel
_______________________________________________
SEL mailing list
SEL at lists.stationary-engine.com
http://www.stationary-engine.com/mailman/listinfo/sel