[SEL] New Way Mixer Re-Casting

[Richard Strobel]

For Steve Royster...Steve, was your picture of the mixer off a 4 1/2 hp.? 
It doesn't match up with the one that I have for a pattern:

http://community.webshots.com/photo/471752277/474997344jgkWft

and here's the one I have... also for Rick Rowlands:

http://community.webshots.com/photo/471752277/532058600yVrGCF  and hit next 
few a few more.

For Rick Rowlands...I've sent you an email with no reply Rick.  Would you 
contact me off list please?


Chester, I need to make some intake tube measurements to make sure that what 
I got, is what I want.

later,
RickinMt.
Richard _Strobel7 at msn.com    remove the space.








----- Original Message ----- 
From: "SERVICE" <edwards_service at westnet.com.au>
To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
Sent: Sunday, January 01, 2006 11:04 PM
Subject: Re: [SEL] New Way Mixer Re-Casting


> Rick, the new way mixer i have copied for my 4.5hp is different to the 
> 3.5hp
> mixers you have shown, i dont know if all the 4.5hp ones are different, 
> but
> hopefully someone can tell us, thanks to your photos i have finished my 
> fan
> & shaft, cheers for now
> Chester from West Aussie.
>
> ----- Original Message ----- 
> From: "Richard Strobel" <Richard_Strobel7 at msn.com>
> To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> Sent: Saturday, December 31, 2005 1:02 AM
> Subject: Re: [SEL] New Way Mixer Re-Casting
>
>
> > Rick, I will work on getting the dimensions today, and some more 
> > pictures
> of
> > the mounting bracket.
> >
> >   Question please to all the New Way owners:
> >
> >  Ya'll know that there's no needle valve.  How do I remove what I'm 
> > going
> to
> > call "the main jet?" i.e. the brass tube with the small hole in the 
> > side?
> > Are there TWO sets of male and female threads..one set on each side of 
> > the
> > mixer?
> >
> >   I also think that on re-assembly the hole (jet) should be positioned
> > straight up and then locked with the external lock nut.  Believe the air
> > rushing around the circumference of the tube would create a low pressure
> > area on the back side where the jet(hole) is, and this would create the
> > "venturi effect."  Please correct me if I'm wrong.
> >
> > Well enuf fer now.
> > Thanks
> > RickinMt.
> > PS:  Are there any decals available?
> >
> >
> >
> > > Rick,
> > >
> > >  What are the dimensions of the casting?  Can you get a picture that
> shows
> > > the mounting brackets?    What is the configuration of the interior of
> the
> > > part?  Would it be possible to cast it solid and just drill out the
> > > passageways inside?  I do have some standard size round cores which I
> > > could
> > > possibly use to save you the trouble of making a core box.
> > >
> > > Rick Rowlands
> > > Tod Engine Works
> > > Makers of Quality iron, steel, ductile iron
> > > and nonferrous castings
> > > 2261 Hubbard Road
> > > Youngstown, OH  44505
> > > 330-728-2799
> > > Fax 330-759-1524
> > > www.todengine.org/engineworks.html
> > _______________________________________________
> > SEL mailing list
> > SEL at lists.stationary-engine.com
> > http://www.stationary-engine.com/mailman/listinfo/sel
>
> _______________________________________________
> SEL mailing list
> SEL at lists.stationary-engine.com
> http://www.stationary-engine.com/mailman/listinfo/sel
>