[SEL] Fooled again

[bill at antique-engines.com]

Unfortunately, it's a bit late now.

I will still buy the longer bits - just because I really should have them!

Bill

> Bill - you need to get yourself some long series drill bits. Since the key
> is so far from the end of the shaft you need to make up a guide as
> previously mentioned and clamp it in the keyway near the flyeheel.
>
> Larry Anger.
>
> bill at antique-engines.com wrote:
> I STILL can't get the key out of my extra sandwich crank/flywheel to
> finish taking it apart.
> I've welded on it, no luck.
> I've tried drilling, but the shaft sticks out so far I can't get the drill
> close enough.
> It's drilled slightly off-center now, so seems I'm SOL.
> Was watching the other discussion on the stuck key, but the shaft on that
> one isn't in the way like it is this one.
> Would be easier if the shaft didn't stick out 3 or 4" beyond the flywheel.
>
> Bill
>
>> Well said George.
>> Keith
>>
>>
>> At 12:19 PM 4/1/2005, you wrote:
>>>
>>>Damn, I thought this was the stationary engine list.
>>>
>>>Maybe this is the Honda forum for discussing oil pan problems.
>>>
>>>Maybe this is the Hammond forum for discussing old organ problems. Sure
>>>a lot of us have organ problems, but there's pills for that and we don't
>>>need to be discussing that here.
>>>
>>>Maybe this is the Transmission forum for talking about transmission
>>>problems and which sequence to use in shifting gears.
>>>
>>>Maybe this is the French car forum.
>>>
>>>Maybe this is the American muscle car forum.
>>>
>>>Maybe this is the computer and software support forum.
>>>
>>>Maybe this is the wheel forum, as lug nuts seem to be a common topic.
>>>
>>>Must be all of the above, since that's what the majority of the postings
>>>are about!
>>>
>>>What does it take to get you folks to post your engine related postings
>>>here and go find the appropriate forums for all the off topic stuff???
>>>
>>>I've got a turbo diesel pickup, and if I have a pickup problem guess
>>>where I post it?
>>>
>>>I've like to fish, and if I have fishing questions or comments there is
>>>a fishing forum I post to.
>>>
>>>I'd like to buy a fishing boat, and again I have a couple boat forums I
>>>belong to.
>>>
>>>When I have computer or website problems, there's forums for that too.
>>>
>>>I would assume that almost any make of vehicle made has a forum where
>>>people love to trade their stories and problems.
>>>
>>>(Maybe taking that double dose of old grouch pills this morning is
>>>kicking in!)
>>>
>>>I've been thrilled that Paul has a gibb key problem! At least he has an
>>>engine problem.
>>>
>>>(actually the pills kicked in so well, I had to reboot this computer a
>>>few sentences ago)
>>>
>>>I'd complain about the Aussie's too, except I like reading their accents
>>>in the postings ;-) I may not be a fan of Aussie engines, but at least
>>>the majority of their postings are on topic.
>>>
>>>I think if some of you tried to get back on topic again and maybe had a
>>>goal of making half your postings engine related (that's antique
>>>engines, not vehicles) I could cut down on all the medications I'm
>>>taking.
>>>
>>>Grumpy George
>>>
>>>
>>>
>>>
>>>
>>>_______________________________________________
>>>SEL mailing list
>>>SEL at lists.stationary-engine.com
>>>http://www.stationary-engine.com/mailman/listinfo/sel
>>
>>
>> _______________________________________________
>> SEL mailing list
>> SEL at lists.stationary-engine.com
>> http://www.stationary-engine.com/mailman/listinfo/sel
>>
>
> _______________________________________________
> SEL mailing list
> SEL at lists.stationary-engine.com
> http://www.stationary-engine.com/mailman/listinfo/sel
>
>
>
> ---------------------------------
> Post your free ad now! Yahoo! Canada Personals
> _______________________________________________
> SEL mailing list
> SEL at lists.stationary-engine.com
> http://www.stationary-engine.com/mailman/listinfo/sel
>