[SEL] Cummins Engine Problem and a question

[Jim Kirkes]

The ALCO SW-1 which was a 600 Hp switcher weighed 100 tons. 
The GE was a rather small switcher.

Jim

Jim and Diane Kirkes
jd.kirkes at verizon.net
----- Original Message ----- 
From: "Rick Rowlands" <rowlands1941 at roadrunner.com>
To: "The SEL email discussion list" 
<sel at lists.stationary-engine.com>
Sent: Tuesday, September 21, 2010 6:57 PM
Subject: Re: [SEL] Cummins Engine Problem and a question


Yes it is a switcher.  GE built switchers from 25 ton 
version powered with
one Cummins truck engine up to 44, 45, 65, 80 and 110 ton 
versions powered
by two engines.

Rick

----- Original Message ----- 
From: "Kangas, James G." <james.kangas at timken.com>
To: "The SEL email discussion list" 
<sel at lists.stationary-engine.com>
Sent: Tuesday, September 21, 2010 8:38 PM
Subject: Re: [SEL] Cummins Engine Problem and a question


Is this Locomotive some type of "Switcher"?I've never heard 
of a Loco with
that small an engine.The 80 tons is what's puzzling me.Seems 
heavy for a
Switching Engine.
 Jim K

________________________________

From: sel-bounces at lists.stationary-engine.com on behalf of 
Rick Rowlands
Sent: Tue 9/21/2010 1:22 PM
To: The SEL email discussion list
Subject: [SEL] Cummins Engine Problem



I had a chance to perform a detailed inspection of the 
Cummins LI-600 diesel
engines on our GE 80 ton locomotive. The front engine is 
stuck, most likely
from water in one or more cylinders. One head is missing and 
the cylinder
wall is a bit rusty so this may be the one that is stuck.

The rear engine does run, however the no. 2 connecting rod 
bearing
disintegrated and apparently the engine was kept in service 
for a while
longer probably until the knock became too much to listen 
to. The crankpin
is now of course galled. I have not yet taken a mic to it to 
find out how
much metal was lost. Actually only one liner was still 
somewhat intact, the
other one was in the bottom of the pan in a million pieces.

I need to be able to move this locomotive under its own 
power to get it out
of where it is at and into a new location for rebuilding, 
probably two miles
total. So I am now thinking if there is a way that I can run 
the engine on
five cylinders for long enough to get it where it needs to 
go.

Some of the issues with doing this would be whether it would 
be better to
try to clean up the journal as much as possible, put in a 
new liner,
disconnect the injector and engage the compression release 
on that cylinder,
or to remove the connecting rod, tie the piston and rod out 
of the way and
install a machined clamp that would provide some of the 
weight of the rod
and seal off the oil hole.

Anyone ever have to do something like this on a diesel 
engine? Would such a
temporary repair work?

For the uninitiated, the LI-600 is a six cylinder inline 
engine, generating
250 HP at 1000 RPM. 7" bore, 10" stroke. Crankpin is 4.25" 
dia. First
produced in 1929, this engine was built in 1944. Parts are 
somewhat
available.

Rick Rowlands
_______________________________________________
SEL mailing list
SEL at lists.stationary-engine.com
http://www.stationary-engine.com/mailman/listinfo/sel





-----------------------------------------
This message and any attachments are intended for the 
individual or
entity named above. If you are not the intended recipient, 
please
do not forward, copy, print, use or disclose this 
communication to
others; also please notify the sender by replying to this 
message,
and then delete it from your system. The Timken Company / 
The
Timken Corporation


--------------------------------------------------------------------------------


> _______________________________________________
> SEL mailing list
> SEL at lists.stationary-engine.com
> http://www.stationary-engine.com/mailman/listinfo/sel
>

_______________________________________________
SEL mailing list
SEL at lists.stationary-engine.com
http://www.stationary-engine.com/mailman/listinfo/sel