[SEL] New New Way Engine

[Tim Christoff]

Thanks John, I do have that one.  You know anyone who has a manual on the
twin's?  I've never seen one.

Tim Christoff
Basehor Kansas


> [Original Message]
> From: John & Beryl Cooper <cooperjb at aapt.net.au>
> To: The SEL email discussion list <sel at lists.stationary-engine.com>
> Date: 2/10/2009 2:13:57 AM
> Subject: Re: [SEL] New New Way Engine
>
> Hi Tim,
> Correct, that is the D11 catalogue.
> Regards,
> John Cooper,\.
> ----- Original Message ----- 
> From: "Tim Christoff" <tchristoff at earthlink.net>
> To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> Sent: Monday, February 09, 2009 1:55 PM
> Subject: Re: [SEL] New New Way Engine
>
>
> >
> > Hi John, is that the D-11 catolog?
> >
> > Tim Christoff
> > Basehor Kansas
> >
> >
> >> [Original Message]
> >> From: John & Beryl Cooper <cooperjb at aapt.net.au>
> >> To: The SEL email discussion list <sel at lists.stationary-engine.com>
> >> Date: 2/9/2009 6:37:10 PM
> >> Subject: Re: [SEL] New New Way Engine
> >>
> >> Hi Tim,
> >> I have recently been given a New Way sales catalogue from the John
Deere
> >> Plow Co. Omaha, Sioux Falls in mint condition approximately 1911
edition.
> >> Your engine is listed almost identical to the picture you supplied.
There
> > is
> >> also a similar engine in a club near here and also a single cylinder
one
> > in
> >> the area.
> >> Have fun,
> >> John Cooper,
> >> Bega Australia.
> >> ----- Original Message ----- 
> >> From: "Tim Christoff" <tchristoff at earthlink.net>
> >> To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> >> Sent: Monday, February 09, 2009 10:55 AM
> >> Subject: [SEL] New New Way Engine
> >>
> >>
> >> >
> >> > I finally got a New Way Twin today, actually, I bought it a few days 
> >> > ago
> >> > but didn't get it until today.  It is a 6 to 7 hp with a nice cast 
> >> > brass
> >> > tag.  The engine is complete and uses a buzz coil for ignition. 
Anyone
> >> > have any knowlege of how the wiring for this would work?  I can only
> > find
> >> > one place to connect the pos wire so I am wondering if just a single
> > coil
> >> > is all that is needed.  You can see a picture of it on Harry's page
via
> >> > this link.  http://www.smokstak.com/forum/showthread.php?t=57053
> >> >
> >> > Tim Christoff
> >> > Basehor Kansas
> >> >
> >> >
> >> >
> >> >
> >> > _______________________________________________
> >> > SEL mailing list
> >> > SEL at lists.stationary-engine.com
> >> > http://www.stationary-engine.com/mailman/listinfo/sel
> >>
> >>
> >>
> >
----------------------------------------------------------------------------
> > ----
> >>
> >>
> >>
> >> No virus found in this incoming message.
> >> Checked by AVG - www.avg.com
> >> Version: 8.0.233 / Virus Database: 270.10.19/1940 - Release Date:
> > 02/08/09
> >> 17:57:00
> >>
> >>
> >> _______________________________________________
> >> SEL mailing list
> >> SEL at lists.stationary-engine.com
> >> http://www.stationary-engine.com/mailman/listinfo/sel
> >
> >
> > _______________________________________________
> > SEL mailing list
> > SEL at lists.stationary-engine.com
> > http://www.stationary-engine.com/mailman/listinfo/sel
>
>
>
----------------------------------------------------------------------------
----
>
>
>
> No virus found in this incoming message.
> Checked by AVG - www.avg.com
> Version: 8.0.233 / Virus Database: 270.10.19/1940 - Release Date:
02/08/09 
> 17:57:00
>
>
> _______________________________________________
> SEL mailing list
> SEL at lists.stationary-engine.com
> http://www.stationary-engine.com/mailman/listinfo/sel