[SEL] Blacksmithing / Anvils

[Andrew]

I'd hate to use a hammer on one after paying that much... Hey Rick, if you
decide to make some I could use a good size anvil on my cable rig!
Andrew.

>From Andrew at
tech at andrew2.netpluscom.com
engineering at andrew2.netpluscom.com
b10730 at hotmail.com

Visit the website at http://www.netpluscom.com/~10730/
http://www.oldengine.org/members/andrew/

On Wed, 3 May 2006, Rick Rowlands wrote:

> I did some research and there is a fellow in the US making steel anvils,
> however I think his prices are a bit on the high side.  How many hobbyist
> blacksmiths can afford to spend $1,450 on a 260 pound anvil, even if it is a
> beautiful piece?
>
> http://www.anvils.nimbaforge.com/
>
> According to his website he has them poured out of 8640 steel and heat
> treated to rockwell 50.   I've made 8640 before and a local heat treater
> will have no problem doing the correct treatment.  We could probably sell a
> comparable anvil at a profit for around $500.  However the anvil would have
> the as cast finish except for the face which I could plane on our 1880s
> Putnam planer or 20" G&E shaper.
>
> I think Curt is interested in making the pattern for this one. I can't pour
> these with my current furnace however I'm agressively looking for a 300
> pound furnace which would be able to handle this size anvil.
>
> Rick Rowlands
> Tod Engine Works
> Makers of Quality iron, steel, ductile iron
> and nonferrous castings
> 249 North Water Avenue
> Sharon, PA 16146
> 330-728-2799
> Fax 330-759-1524
> www.todengine.org/engineworks.html
>
>
>
>  ----- Original Message -----
> From: "Steve W." <falcon at telenet.net>
> To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> Sent: Wednesday, May 03, 2006 9:55 AM
> Subject: Re: [SEL] Blacksmithing (a tad OT) bringing the next generation
> along.
>
>
> > Not sure what steel it is but it runs about .40 points of carbon
> > content. The main problem is that the face isn't heat treated evenly so
> > some have soft areas. What kind of money would you be talking and how
> > large could you pour? There is actually a LARGE market for a good steel
> > anvil made in the US.
> >
> > Steve Williams
> > Near Cooperstown, New York
> >
> >
> > ----- Original Message -----
> > From: "Rick Rowlands" <jrrowlands at neo.rr.com>
> > To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> > Sent: Tuesday, May 02, 2006 6:23 PM
> > Subject: Re: [SEL] Blacksmithing (a tad OT) bringing the next generation
> > along.
> >
> >
> >> I'll make you one out of real steel (8630 heat treated) once I get the
> >> larger furnace installed.  Who knows what that russian stuff is.
> >>
> >> Rick
> >>
> >> ----- Original Message -----
> >> From: "Steve W." <falcon at telenet.net>
> >> To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> >> Sent: Tuesday, May 02, 2006 4:05 PM
> >> Subject: Re: [SEL] Blacksmithing (a tad OT) bringing the next
> > generation
> >> along.
> >>
> >>
> >> > Want a decent anvil for a GOOD price? Wander into Harbor Freight and
> > buy
> >> > the 110 pound RUSSIAN imported steel anvil they sell. I have two of
> > them
> >> > and they work  well once you reshape the nose and clean up the face.
> > I
> >> > do blade smithing on mine and use the other to make "iron" items for
> >> > other folks.
> >> > I also have a 200 pounder that I found cheap.
> >> >
> >> > Steve Williams
> >> > Near Cooperstown, New York
> >> >
> >> > Pacifism - The theory that if they'd fed
> >> > Jeffrey Dahmer enough human flesh,
> >> > he'd have become a vegan.
> >> >
> >> > ----- Original Message -----
> >> > From: "Curt" <curt at imc-group.com>
> >> > To: "SEL" <sel at lists.stationary-engine.com>; "SEL (Oldengine.org)"
> >> > <stationary-engine at oldengine.org>
> >> > Sent: Tuesday, May 02, 2006 2:49 PM
> >> > Subject: [SEL] Blacksmithing (a tad OT) bringing the next generation
> >> > along.
> >> >
> >> >
> >> >> We've attended the SIAM show for quite a few years and this is a
> > show
> >> >> Devin particularly enjoys in large part because of the blacksmith
> >> > there.
> >> >> He has been very patient with Devin thru the years as he hung
> > around
> >> >> poking the fire and cranking the blower. In time the fellow has let
> >> > him
> >> >> do more and more and Devin seems to be picking up a strong interest
> > in
> >> >> this part of the old iron hobby.
> >> >> For those at Portland in the SEL area last fall, you may recall
> > Devin
> >> >> picked up a forge blower. For his birthday last weekend (now a
> >> > teenager)
> >> >> we picked up a forge pan from Clayton Ballard that was missing all
> > the
> >> >> built in blower parts. This was perfect as Devin had a stand alone
> >> >> blower. I made a air entrance and elbow to attach the temporary
> > hose
> >> > to
> >> >> (shop vac hose) and Devin gave it a whirl on Sunday evening. Missy
> > and
> >> > I
> >> >> sat and had our afternoon drink (her Scotch, my beer) and enjoyed
> > the
> >> >> entertainment Devin provided. I took a couple of pictures and they
> > are
> >> > here:
> >> >>
> >> >
> > <http://www.oldengine.org/members/holland/images/BlacksmithDevin/Thumbna
> >> > ils.html>
> >> >> The little anvil he is using is a tad small, so we may be on the
> >> > lookout
> >> >> for a decent sized anvil. Believe we will also set up a little area
> > in
> >> >> the backyard with a roof for him to 'smith in. He definitely needs
> > to
> >> > be
> >> >> further away from the house as the coal smoke will soon soot up the
> >> > side
> >> >> of the house!
> >> >> Missy and I are quite encouraged that he is showing interest in
> > this
> >> >> even as the teen years are beginning. Kids need something
> > productive
> >> >> that keeps them challenged and interested in contrast to all the
> > other
> >> >> temptations available to them at this age.
> >> >> Not many pictures to look at on the link yet, but we hope you enjoy
> >> > them.
> >> >> Curt & Missy Holland
> >> >> Gastonia, NC
> >> >>
> >> >> _______________________________________________
> >> >> SEL mailing list
> >> >> SEL at lists.stationary-engine.com
> >> >> http://www.stationary-engine.com/mailman/listinfo/sel
> >> >>
> >> >
> >> > _______________________________________________
> >> > SEL mailing list
> >> > SEL at lists.stationary-engine.com
> >> > http://www.stationary-engine.com/mailman/listinfo/sel
> >>
> >> _______________________________________________
> >> SEL mailing list
> >> SEL at lists.stationary-engine.com
> >> http://www.stationary-engine.com/mailman/listinfo/sel
> >>
> >
> > _______________________________________________
> > SEL mailing list
> > SEL at lists.stationary-engine.com
> > http://www.stationary-engine.com/mailman/listinfo/sel
>
> _______________________________________________
> SEL mailing list
> SEL at lists.stationary-engine.com
> http://www.stationary-engine.com/mailman/listinfo/sel
>