[SEL] New Way Mixer Re-Casting

[Steve Royster]

Hi Rick, Mine is a 3-1/2 hp! Steve


>From: "Richard Strobel" <Richard_Strobel7 at msn.com>
>Reply-To: The SEL email discussion list <sel at lists.stationary-engine.com>
>To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
>Subject: Re: [SEL] New Way Mixer Re-Casting
>Date: Mon, 2 Jan 2006 06:15:34 -0700
>
>For Steve Royster...Steve, was your picture of the mixer off a 4 1/2 hp.?
>It doesn't match up with the one that I have for a pattern:
>
>http://community.webshots.com/photo/471752277/474997344jgkWft
>
>and here's the one I have... also for Rick Rowlands:
>
>http://community.webshots.com/photo/471752277/532058600yVrGCF  and hit next
>few a few more.
>
>For Rick Rowlands...I've sent you an email with no reply Rick.  Would you
>contact me off list please?
>
>
>Chester, I need to make some intake tube measurements to make sure that 
>what
>I got, is what I want.
>
>later,
>RickinMt.
>Richard _Strobel7 at msn.com    remove the space.
>
>
>
>
>
>
>
>
>----- Original Message -----
>From: "SERVICE" <edwards_service at westnet.com.au>
>To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
>Sent: Sunday, January 01, 2006 11:04 PM
>Subject: Re: [SEL] New Way Mixer Re-Casting
>
>
> > Rick, the new way mixer i have copied for my 4.5hp is different to the
> > 3.5hp
> > mixers you have shown, i dont know if all the 4.5hp ones are different,
> > but
> > hopefully someone can tell us, thanks to your photos i have finished my
> > fan
> > & shaft, cheers for now
> > Chester from West Aussie.
> >
> > ----- Original Message -----
> > From: "Richard Strobel" <Richard_Strobel7 at msn.com>
> > To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> > Sent: Saturday, December 31, 2005 1:02 AM
> > Subject: Re: [SEL] New Way Mixer Re-Casting
> >
> >
> > > Rick, I will work on getting the dimensions today, and some more
> > > pictures
> > of
> > > the mounting bracket.
> > >
> > >   Question please to all the New Way owners:
> > >
> > >  Ya'll know that there's no needle valve.  How do I remove what I'm
> > > going
> > to
> > > call "the main jet?" i.e. the brass tube with the small hole in the
> > > side?
> > > Are there TWO sets of male and female threads..one set on each side of
> > > the
> > > mixer?
> > >
> > >   I also think that on re-assembly the hole (jet) should be positioned
> > > straight up and then locked with the external lock nut.  Believe the 
>air
> > > rushing around the circumference of the tube would create a low 
>pressure
> > > area on the back side where the jet(hole) is, and this would create 
>the
> > > "venturi effect."  Please correct me if I'm wrong.
> > >
> > > Well enuf fer now.
> > > Thanks
> > > RickinMt.
> > > PS:  Are there any decals available?
> > >
> > >
> > >
> > > > Rick,
> > > >
> > > >  What are the dimensions of the casting?  Can you get a picture that
> > shows
> > > > the mounting brackets?    What is the configuration of the interior 
>of
> > the
> > > > part?  Would it be possible to cast it solid and just drill out the
> > > > passageways inside?  I do have some standard size round cores which 
>I
> > > > could
> > > > possibly use to save you the trouble of making a core box.
> > > >
> > > > Rick Rowlands
> > > > Tod Engine Works
> > > > Makers of Quality iron, steel, ductile iron
> > > > and nonferrous castings
> > > > 2261 Hubbard Road
> > > > Youngstown, OH  44505
> > > > 330-728-2799
> > > > Fax 330-759-1524
> > > > www.todengine.org/engineworks.html
> > > _______________________________________________
> > > SEL mailing list
> > > SEL at lists.stationary-engine.com
> > > http://www.stationary-engine.com/mailman/listinfo/sel
> >
> > _______________________________________________
> > SEL mailing list
> > SEL at lists.stationary-engine.com
> > http://www.stationary-engine.com/mailman/listinfo/sel
> >
>_______________________________________________
>SEL mailing list
>SEL at lists.stationary-engine.com
>http://www.stationary-engine.com/mailman/listinfo/sel