[SEL] New Way engine

SERVICE edwards_service at westnet.com.au
Wed Apr 6 20:49:13 PDT 2005


Hi Tim,
from what iv been told the breather is a small hole only, no pipe or
fitting, about 1/8 diameter, thanks for looking.
Chester.




----- Original Message ----- 
From: "Tim Christoff" <tchristoff at earthlink.net>
To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
Sent: Thursday, April 07, 2005 11:15 AM
Subject: Re: [SEL] New Way engine


> Chester, I went and had a look at my 4 1/2 upright today and there is no
> gas breather pipe on it.  I have had it down to bare metal and would have
> remembered one if there was one.  My 2 1/2 upright does have one though.
I
> have just finished up the painting on the 4 1/2 so I don't know how well
it
> will work without a breather hole yet, might have to make one.
>
> Tim Christoff
>
>
> > [Original Message]
> > From: SERVICE <edwards_service at westnet.com.au>
> > To: The SEL email discussion list <sel at lists.stationary-engine.com>
> > Date: 4/7/2005 11:39:13 AM
> > Subject: Re: [SEL] New Way engine
> >
> > Hi guys, thanks for the input, Peter i have had a look at Bobs and his
is
> on
> > the governor side and he has a pop rivit in it, his is a 3.1/2hp, so it
> was
> > hard to work out exact spot on mine, i have been told that the engines
> with
> > breather on the side are later than engines with breather near fuel
> filler.
> > Thanks again,
> > Chester.
> >
> >
> >
> >
> >
> >
> >
> >
> > ----- Original Message ----- 
> > From: "peter ogborne" <jopeter at omninet.net.au>
> > To: "The SEL email discussion list" <sel at lists.stationary-engine.com>
> > Sent: Wednesday, April 06, 2005 7:11 PM
> > Subject: Re: [SEL] New Way engine
> >
> >
> > > Chester ....one of the boys up at Midland is going to send me  a pic .
I
> > am
> > > also going to see Bob  Bailey on Friday morning , i will have a look
at
> > his
> > > Newway and send you a picture.........might save you getting the iron
> > > filings as Arnie suggests!
> > > ----- Original Message ----- 
> > > From: "Arnie Fero" <fero_ah at city-net.com>
> > > To: "Stationary Engine List" <sel at lists.stationary-engine.com>
> > > Sent: Tuesday, April 05, 2005 11:51 PM
> > > Subject: Re: [SEL] New Way engine
> > >
> > >
> > > > Hi Chester,
> > > >
> > > > This is a wild shot...  If you don't get any positive suggestions as
> to
> > > > where the hole might be, it's just possible that a Magnaflux
technique
> > > > might work.  I'd recommend looking the process up on the web, but I
> > think
> > > > basically you turn your crankcase into an electromagnet and dust it
> with
> > > > iron filings.  Normally used to find cracks, but it should also work
> to
> > > > find a plastic-filled small hole.  Good luck.  If it works, post the
> > > > "success story."  If it doesn't, forget I ever said anything.  8-))
> > > >
> > > > See ya,  Arnie
> > > >
> > > > Arnie Fero
> > > > Pittsburgh, PA
> > > > fero_ah at city-net.com
> > > >
> > > > On Tue, 5 Apr 2005, SERVICE wrote:
> > > >
> > > >> Hi guys, i am currently restoring a vertical new way, it is a 4.5hp
> > > >> hinged crankcase hit miss, the previous owner started restoring
this
> > and
> > > >> has filled & painted over the fuel tank breather hole, i am trying
to
> > > >> find either pictures or a diagram of where this hole is located as
i
> am
> > > >> going to have to redrill it, i belive some engines had the hole on
> the
> > > >> governor side & some had it on the front fuel filler side depending
> on
> > > >> build date, the hole is approx 1/8 in dia ?.  Appreciate any
> comments,
> > > >> thanks.
> > > >> Chester from West Aussie.
> > > >
> > > > _______________________________________________
> > > > SEL mailing list
> > > > SEL at lists.stationary-engine.com
> > > > http://www.stationary-engine.com/mailman/listinfo/sel
> > > >
> > > >
> > >
> > >
> > > _______________________________________________
> > > SEL mailing list
> > > SEL at lists.stationary-engine.com
> > > http://www.stationary-engine.com/mailman/listinfo/sel
> >
> > _______________________________________________
> > SEL mailing list
> > SEL at lists.stationary-engine.com
> > http://www.stationary-engine.com/mailman/listinfo/sel
>
>
>
> _______________________________________________
> SEL mailing list
> SEL at lists.stationary-engine.com
> http://www.stationary-engine.com/mailman/listinfo/sel




More information about the sel mailing list